Soil Testing Equipment

Product Details:

The unit consists of a pressure vessel with clamp for sealing cap, rubber sealing gasket, pressure gauge calibrated in percentage moisture content 0-25% x 1% on the wet weight basis, a counterpoised balance for weighing sample, a scoop for measuring carbide reagent, a bottle of reagent, one cleaning brush and a set of 4 steel balls for thorough mixing. Complete in highly polished wooden carrying case with handle.

Product Details:

Product Details:

For determining the Liquid Limit of soils. This is specially useful to obtain reliable and accurate results for those soils which have low plasticity index. The percenetage moisture contents determined when a cone with half angle of 15 - 30 minutes under a total sliding weight of 148 gm penetrates 25 mm gives the Liquid Limit.
Consists of a vertical pillar mounted on a base provided with leveling screw The head together with dial gauge rod and cone (or needle) slides on a pillar and can be clamped at required height. A rack and pinion and pointer assembly provides adjustment of needle or cone tip to sample.  It incorporates a slipping clutch mechanism which make reading of penetration, and subsequesnt restting a simple and accurate operation
The dial is graduated in 400 1/10th mm sub-divisions,  and the red needle pointer against black figures makes for easy reading.
Suplied complete with 50 mm dia x 50 mm high cup complete with stainless steel cone  50 mm x 40mm dia high made  of gunmetal.

Additional Information:

• Packaging Details: Box Type

Product Details:

Proving Rings are used for load meassurements and are used in the outfits of a number of soil/cement & bitumen testing equipments like Direct Shear Apparatus. Triaxial
Shear test Apparatus, CBR Test. Unconfined Test, Marshall
Test etc. They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy
When compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed.
This deformation is measured by a sensitive
dial gauge fixed co-axially at the centre of the proving ring
The dial readings thus obtained versus load applied enable the operator to findout unknown load,, just by noting the dial gauge reading for the unknown load.
The proving rings have hogh elasticity and on removing load they regain the orginal shape provided they are loaded in their elastic limits.
The dial gauge and plunger anvil are mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remotest chance of shifting due to inadvertent shocks or pressure exerted on it. The dial gauge plunger rests on an adjustable anvil.
Proving Rings from 50 kg to, 1,00,000 kg capacity provided with 1/2 inch B.S.F. female threads. Loading bossess and a loading ball nipple and steel ball are supplied with each rings
Rings of capacity over 25000kgf (or 25 tonnes) are not thus threaded.
Each ring is individually calibrated and supplied with works calibration charts and a carrying case.
Calibration charts from Standard Laboratories for the proving rings ordered are also available at extra cost. All Proving rings are Integrall type. Integral type compressicve Proving Rings of different capacities from 50 kgf to 200000 kgf are available

Product Details:

Direct Shear Apparatus same as RSEP-067, but unit is electrically operated to give the following 12 rates of stains of strains 1.25, 0.625, 0.125, 0.05, 0.025, 0.01, 0.005, 0.002, 0.001, 0.0004 and 0.0002 mm/min.The apparatus is suitable for operation on 230 volts single phase A.C. supply. without dial gauge and proving ring.

Product Details:

Rotap Motorized Sieve Shaker to make process of sieving simpler and quicker . Rotap sieve shaker is useful. This produces circular shaking of the sieves at the same time the sieves are tapped. The mechanism for imparting circular action and tapping is oil immersed in a tank and is motorized. The shaker can accommodate upto 7 nos. sieve of dia 150mm or 200mm. Suitable operation of 230 volts A.C. supply single phase. Same as above but fitted with time switch

Product Details:

Liquid Limit Device Fitted with a counter to register the number of bellows.

Additional Information:

• Item Code: RSEP-114

Product Details:

U-bracket and swivel head. Penetration piston, 50mm dia threaded at the upper end. Extension rods set consisting of lengths 5cm, 2 lengths 10cm, 1length 30cm, 1 length 50cm, and 1 length 100cm, used as spacers between the proving ring and penetration piston. The lengths are machined from steel tubing. Connector set has eight connectors for coupling the penetration piston and proving ring assembly either directly or through extension pieces. Dial gauge support of seamless pipe construction. It stands 30cm high and 45cm wide at the base. Provided with a quick release screw type clamp capable of sliding and locking anywhere along the 2-meter length of the bridge. Supplied with annular metal weight 5 kg, 250mm dia with 53mm dia central hole, slotted metal weight 5 kg, 215 mm to 250 mm dia with 53mm dia slot, 2 Nos, Slotted metal weight 10 kg 215mm to 250mm dia with 53mm dia slot 2 Nos.

Product Details:

Gyratory Sieve Shaker carries upto 7 sieves of 150mm or 200mm diameter. The shaker is driven by a ¼ h.p (motor through a reduction a reduction gear immersed in oil. The sieve table does not rotate but is inclined from the vertical axis and the direction of inclination changes progressively in a clockwise direction. If the stop-pin below the table is removed, the shaker can have a rotary motion. In addition to this gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. a pair of rods and holder are supplied. The holder can be fixed on the top of the uppermost sieves and thus the sieve set is firmly held. Suitable for operation on 230 Volts, 50 cycles single phase, A.C. Supply.

Product Details:

The Equipment consists one each of :
Vibratory table, with a cushioned steel vibrating deck about 75 cm x 75cm. It has a frequency of approximately 3600vibrations per minute under a 115 kg load. Amplitude is variable 0.45mm and 0.45 to 0.65mm. Suitable for operation on 415 volts three phase supply.Cylindrical metal unit weight mold, 3000 mlcapacity.Guide Sleeve with clamp assembly.Surcharge base plate for mould.Handle for surcharge base plateSurcharge weight. The total weight together with surcharge base plate and handle is equivalent to 140 kg/sq.cm. For mold Cylindrical metal unit weight mold, 15000ml capacity. Surcharge base plate for guide sleeve.Surcharge weight for the cylindrical mold of the 15000ml cap. (Total weight together with the above mold & surcharge weight is equivalent to 140 kg/sq.cm. Dial gauge holder & Calibration bar 75 x 300mm x 3mm.

Product Details:

Product Details:

Consists of following :Hydraulic Centre Jack. 250 kN (25T) capacity with 54 mmcentre hole, 150 mm ram travel double acting.Hand operated two stage pump .Rubber hose 6 mm long with pair of quick couplings.Load gauge 150 mm dia, 250 KN x 5 KN.

Additional Information:

• Item Code: Rajco
• Delivery Time: Time
• Packaging Details: Consists of following :Hydraulic Centre Jack. 250 kN (25T) capacity with 54 mmcentre hole, 150 mm ram travel double acting.Hand operated two stage pump .Rubber hose 6 mm long with pair of quick couplings.Load gauge 150 mm dia, 250 KN x 5 KN.

Product Details:

It consists of a cone fixed to a movable bearing rod.
Arrangement is provided to clamp the rod at any desired position
A graduated scale is fixed to the bracket.
Complete with cup 50 mm dia and 50 mm high.

Additional Information:

• Packaging Details: Box packing

Product Details:

Consists of a  torque head adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of a hand wheel which operates a worm gear arrangement turning the upper end of a calibrated torsion spring,  Vane dia,  rod dia,  vane size & vane height are as per IS specification.
The Vane shaft is attached through the hollow upper shaft to resettable pointer,  which indicates the angle of torque on a dial graduated in degress.  The dial reading multiplied by spring factory gives the torque.  A container for soil sample is also supplied,  and a sampiling tube of 38mm I.D. & 150 mm long can also be used as container 6 kgcm,  and 8 kg cm. Complete as above in a wooden carrying case.

Product Details:

Product Details:

Product Details:

Additional Information:

• Packaging Details: box packing

Product Details:

Other details:

• (Stationary Bushing) For 38mm dia specimen.
• Loading pad made of Perspex for 38 mm dia specimens.
• Pair of Plain discs made of Perspex x 38mm dia specimens.
• Pair of Porous stone 38mm dia x 6mm thick.
• Split sand former for 38mm dia specimen
• One dozen rubber sheaths for 38mm dia samples.
• For synthetic rubber ‘O’ rings for 38mm dia specimen.
• One plastic drainage tube.

Product Details:

We are engaged in offering this Load Frame to our valuable customers.

Features:

• Good strength
• Easy to use
• Corrosion proof
• Long Life

Product Details:

Rajco Air Entrainment Meter:

The apparatus Consists of a pressure tight flanged cylindrical measuring bowl of 0.005 cubic meter capacity for maximum size of aggregate 38 mm.  The bowl is fitted with a removable flanged conical cover assembly with the help of a seal. The conical cover has an  air valve and pet a cock for bleeding off the water. A transparent cylindrical stand pipe, which is graduated in air content is fixed to the conical cover assembly. Pressure is applied to the specimen with the help of Pressure bulb and the pressure is recorded on the Pressure gauge which is mounted on the stand pipe. The whole assembly is mounted on a flat base. The instrument is supplied coplete with one each Calibration cylinder with spring clamp, Tamping rod, straight edge, Rubber mallet and Measure.

Additional Information:

• Item Code: RSEP-064
• Production Capacity: 1000
• Delivery Time: Time
• Packaging Details: Leaders in designing, manufacturing and exporting material testing equipment like Jaw Crusher, Laboratory Jaw Crusher around the globe, we at Rajco Scientific Engineering Products, meet the needs of materials engineers,

Product Details:

For collecting undisturbed samples of 38 mm dia for Triaxial shear strength and Unconfined Compressive strength either straight from the field or from a sample of large diameter. The wall thickness is maintained approximately 1.6mm with an area ratio approximately 17 percent.  Both relieved and unrelieved sampling tubes are available.  In the relieved type of tube, the internal diameter is relieved by about 0.5mm of tube, the internal diameter is relieved by about 0.5mm (Inside cllearance 2%, beyond approx. 19 mm length from the cutting edge of the tube, this is most suitable for highly cohesive soils. In the unrelieved type, the internal diameter is uniform throught, thiis type is most suitable for soils of low cohesion. These 38mm dia tubes are available in different lengths.