Concrete & Rock Testing Machine

Product Details:

Consists of a barrell in which is housed a hammer mass attached to an impact spring which slides on a guide bar. A plunger is attached to the guide bar which is pressed against surface to be tested, on reaching the compressive strength, the hammer  mass is released and rebounds to a certain extent (according to the strength of the surface, which is indicated by a rider on a calibrated scale ® A lock button fixed on the body of the hammer locks the rider in place and the rider can be recared to zero position by using the same button.  The equivalent compressive strength can be computed from the chart supplied.  Each hammer is calibrated against a standard test hammer ; and is suitable for specimen of compressive strengths 100-700kg/cm.
The instrument, complete with a grinding stone for polishing the test surface, is supplied in carring case.

Product Details:

RSEP-134 Rajco Cube Mould, with base plate : AS PER IS : 516
These are available in different size and are made according to Indian and British Standards. For the metric size cube moulds the faces are machined flat to +/-0.2mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0,01 inches and finished to within 0.01in. All moulds are supplied complete with base plate.

RSEP-134 Cube Mould 5cm x 5cm x 5cm
Made of Cast Iron

Made of Mild steel

RSEP-135 Cube Mould, 7.06cm x 7.06cm with base plate.
Made of Cast Iron

RSEP-136 Made of Mild Steel.

RSEP-137 Cube Mould, 10cm x 10cm with base plate.

Made of Cast Iron

Made of Mild Steel

RSEP-138 Cube Mould, 15cm x 15cm with base plate made of
Cast Iron
. DO-ISI Mark
Do-Heavy

RSEP-139 Cube Mould, 20cm x 20cm with base plate.
Made of Cast Iron

RSEP-140 Cube Mould, 30cm x 30cm with base plate
Made of Cast Iron

Product Details:

Additional Information:

• Item Code: RSEP-0622
• Production Capacity: 100
• Delivery Time: Time
• Packaging Details: Leaders in designing, manufacturing and exporting material testing equipment like Jaw Crusher, Laboratory Jaw Crusher around the globe, we at Rajco Scientific Engineering Products, meet the needs of materials engineers,

Product Details:

Percentage Refuse Density is defined as the ratio of the initial dried bulk density of the sample to the final density (refusal density) expressed as a percentage.
The sample bulk density is determined by weighing in air
and water. It is then heated in a split mould and compacted
to refusal using a vibrating hammer. The final density is
obtained by weighing in air and water .

Product Details:

Product Details:

It is for conducting Brazilian Test on 75 mm Dia x 25 mm thick the samples and can be used motor tube also. Comprises of a hand operated hydraulic Jack provided with self-retracting piston fixed on the base of a load frame. Loads are recorded on a pressure gauge 0.5 tonnes x 25 kg. And maximum pointer is provided for the breaking of the load indication. Semi-Cylindrical loading strips are provided for Brazilian test and two hardened and ground platens are provided for a compression test.

Additional Information:

• Pay Mode Terms: Other

Product Details:

Light weight laboratory concrete mixer is designed to remove the burdensome work of hand  mixing. Uniform, throughly mixed batches can be produced in the field and laboratory.
The counter balanced mixing drum is easy to  tilt two cubic feet mix capacity.  Total drum volume is 3 cubic feet. Mounted on a strudy rubber tyred stand.  Drum is mounted for end discharge equipped with end towing pole.  Suitable for operation on 220 Volt single phase, 50 cycle, A.C. Supply.

Product Details:

Serological Water Bath with an accuracy of plus-minus 0.5deg.C. Double walled inside a stainless steel and outside mild steel sheet painted in epoxy powder coating. Bath consists of two pilot lamp, temp. control knob and ON/OFF SWITCH. TO WORK ON 220/230 volts A.C. Supplied with or without stirring arrangement without racks and thermometer. The lid of the water bath is made of stainless steel 304 Qlty.

Other Details:

• Size: 330 x 300 x 175 mm (suitable for 4 racks)
• Size: 455 x 300 x 175 mm (suitable for 6 racks)
• Size: 605 x 300 x 175 mm (suitable for 8 racks)

Product Details:

The machine consists of a hand frame. The lower platen has two rollers the distance between which is adjustable For 150 mm x 150 mm x 700 mm beam, the center distance between rollers is 600 mm, while it is 400 mm for beams of size 100mm x 100mm x500mm. The upper platen has also a pair of rollers whose distance is adjustable. It is 200mm centre to centre, for 150mm x 150mm x 700mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. A pressure gauge to indicate load is fixed on the load frame. A small pumping unit is attached to the load frame. The total capacity of the machine is 100 KN and a 150mm dia pressure gauge 0-100 KN x 1 KN is fitted on the machine Since this is a hand operated the lightweight machine, it is useful for field laboratory also.

Product Details:

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer),Other

Product Details:

Container ring of 100 mm diameter and 500mm high, held between a bottom plate and a water cell. The water cell of 10mm diameter brass cylinder and the top and bottom plates of brass or any other non-corroding metal. Each cell with collar is clamped in between a base plate and a top plate with the help of tension rods and nuts. The cell assembly is mounted on the stand. The top plate is provided with an inlet and air release vent and the base plate is provided with an outlet. Complete with a pressure chamber fitted with a pressure regulator and pressure gauge 0-7 kg/cm sq. indicating the test pressure with a single gauge without an air compressor and foot pump.